Hardware Specifications | |
---|---|
Copper Ports | 6 10/100/1000BASE-T waterproof and dustproof RJ45 auto-MDI/MDI-X ports |
PoE Injector Port | 4 ports with 802.3at/af PoE injector function (Port-3 to Port-6) |
Switch Architecture | Store-and-Forward |
Switch Fabric | 12Gbps/non-blocking |
Throughput | 8.9Mpps@64bytes |
Address Table | 8K entries, automatic source address learning and aging |
Shared Data Buffer | 4Mbits |
Flow Control | IEEE 802.3x pause frame for full-duplex Back pressure for half-duplex |
Jumbo Frame | 9Kbytes |
Reset Button | < 5 sec: System reboot > 5 sec: Factory default |
Dimensions (W x D x H) | 103 x 68.3 x 163 mm |
Weight | 1069g |
LED | System: DC1 (Green), DC2 (Green), Fault (Red) Ring (Green), R.O. (Green) 10/100/1000T RJ45 Interfaces (Port 1 to Port 2): LNK/ACT (Green) 10/100/1000T RJ45 Interfaces (Port 3 to Port 6): LNK/ACT (Green) PoE-in-Use (Orange) |
Power Consumption | Max. 160 watts/545.9 BTU |
Power Requirements | Dual 48~56V DC (>53V DC for PoE+ output recommended) |
EFT Protection | 6KV DC |
ESD Protection | 6KV DC |
PoE Standard | IEEE 802.3af/802.3at PoE/PSE |
PoE Power Supply Type | End-span |
PoE Power Output | IEEE 802.3af Standard - Per port 48V~53V DC (depending on the power supply), max. 15.4 watts IEEE 802.3at Standard - Per port 53V~56V DC (depending on the power supply), max. 36 watts |
Power Pin Assignment | 1/2(+), 3/6(-) |
PoE Power Budget | 144 watts max. (depending on power input) |
PoE Ability | PD @ 7 watts: 4 units PD @ 15.4 watts: 4 units PD @ 30.8 watts: 4 units |
Layer 2 Management Functions | |
Port Configuration | Port disable/enable Auto-negotiation 10/100/1000Mbps full and half duplex mode selection Flow control disable/enable |
Port Status | Display each port’s speed duplex mode, link status, flow control status, auto-negotiation status, trunk status |
Port Mirroring | TX/RX/Both Many-to-1 monitor |
VLAN | 802.1Q tagged based VLAN Q-in-Q tunneling Private VLAN Edge (PVE) MAC-based VLAN Protocol-based VLAN Voice VLAN IP Subnet-based VLAN MVR (Multicast VLAN registration) Up to 255 VLAN groups, out of 4095 VLAN IDs |
Link Aggregation | IEEE 802.3ad LACP/static trunk 3 groups with 2 port per trunk |
Spanning Tree Protocol | IEEE 802.1D Spanning Tree Protocol (STP) IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) IEEE 802.1s Multiple Spanning Tree Protocol (MSTP) |
QoS | Traffic classification based, Strict priority and WRR 8-level priority for switching: - Port number - 802.1p priority - 802.1Q VLAN tag - DSCP/ToS field in IP packet |
IGMP Snooping | IGMP (v1/v2/v3) snooping, up to 255 multicast groups IGMP querier mode support |
MLD Snooping | MLD (v1/v2) snooping, up to 255 multicast groups MLD querier mode support |
Access Control List | IP-based ACL/MAC-based ACL Up to 256 entries |
Bandwidth Control | Per port bandwidth control Ingress: 100Kbps~1000Mbps Egress: 100Kbps~1000Mbps |
Layer 3 Functions | |
IP Interfaces | Max. 8 VLAN interfaces |
Routing Table | Max. 32 routing entries |
Routing Protocols | IPv4 software static routing IPv6 software static routing |
Management | |
Basic Management Interfaces | Telnet/Web browser/SNMP v1, v2c |
Secure Management Interfaces | SSH, SSL, SNMP v3 |
SNMP MIBs | RFC 1213 MIB-II RFC 1493 Bridge MIB RFC 1643 Ethernet MIB RFC 2863 Interface MIB RFC 2665 Ether-Like MIB RFC 2819 RMON MIB (Group 1, 2, 3 and 9) RFC 2737 Entity MIB RFC 2618 RADIUS Client MIB RFC 2863 IF-MIB RFC 2933 IGMP-STD-MIB RFC 3411 SNMP-Frameworks-MIB RFC 4292 IP Forward MIB RFC 4293 IP MIB RFC 4836 MAU-MIB IEEE 802.1X PAE LLDP Power over Ethernet MIB |
Standards Conformance | |
Regulatory Compliance | FCC Part 15 Class A, CE |
Standards Compliance | IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab Gigabit 1000T IEEE 802.3x flow control and back pressure IEEE 802.3ad port trunk with LACP IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1s Multiple Spanning Tree Protocol IEEE 802.1p Class of Service IEEE 802.1Q VLAN tagging IEEE 802.1X Port Authentication Network Control IEEE 802.1ab LLDP IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus RFC 768 UDP RFC 793 TFTP RFC 791 IP RFC 792 ICMP RFC 2068 HTTP RFC 1112 IGMP v1 RFC 2236 IGMP v2 RFC 3376 IGMP v3 RFC 2710 MLD v1 FRC 3810 MLD v2 |
Environment | |
Operating | Temperature: -40 ~ 75 degrees C Relative Humidity: 5 ~ 95% (non-condensing) |
Storage | Temperature: -40 ~ 80 degrees C Relative Humidity: 5 ~ 95% (non-condensing) |
Search Products
Search Products
IGS-604HPT-RJ
Complies with IEEE 802.3at High Power over Ethernet end-span PSE
Complies with IEEE 802.3af Power over Ethernet end-span PSE
Up to 4 ports of IEEE 802.3af/802.3at devices powered
Supports PoE Power up to 36 watts for each PoE port
- Description
- Specification
- Application
Acceptable in an industrial setting
Industrial Managed Ethernet Switch PLANET IGS-604HPT-RJ has a 4-port 10/100/1000T 802.11ac switch with an IP67-rated industrial enclosure.A high level of immunity to electromagnetic interference and powerful electrical surges, which are typically found on plant floors or in curb-side traffic control cabinets, is provided by 3at PoE, 2-port 10/100/1000T, and static Layer 3 routing. It is simple to mount the IGS-604HPT-RJ on a wall or DIN rail, which takes up less room. The four Gigabit PoE+ ports each have a 36-watt power capacity, thus even without taking into account the various PoE applications being used, a total power budget of up to 144 watts can be used concurrently. Additionally, it offers small businesses and corporations a quick, secure, and affordable Power over Ethernet network solution for IP security cameras.
Dust- and water-resistant RJ45 Ethernet connector with shielded plug
The IGS-604HPT-RJ comes with a 4-port IEEE 802.3at PoE+ (Port 3 to Port 6) and 6-port 10/100/1000BASE-T auto-negotiation waterproof and dustproof RJ45 connector. Each PoE port has a 36-watt PoE output. The standard UTP cable can become waterproof and dustproof by using these shielded RJ45 plugs. It ensures a tight and strong connection and has an IP67 industrial protection certification, which means it can endure humidity, filth, dust, stress, vibrations, heat, and cold. When coupled to the waterproof and dustproof RJ45 connector.
Environmentally Resistant Architecture
The IGS-604HPT-RJ can work in a temperature range of -40 to 75 degrees C and can shield itself from dust and water infiltration. In any challenging environment, all of these features guarantee the highest level of reliability for mission-critical applications.
High Availability Network System Dual Power Input
To increase system dependability and uptime, the IGS-604HPT-RJ has a robust dual power input system (Dual 48V56V DC) integrated into the customer's automation network. For instance, the hardware failover mechanism will be enabled automatically to keep powering the IGS-604HPT-RJ alternately via DC Power 2 without any loss of operation when DC Power 1 fails to function.
Gigabit Ethernet PoE Networking with Centralized Power Management
The IGS-604HPT-RJ has high-performance Gigabit IEEE 802.3af PoE (up to 15.4 watts) and IEEE 802.3at PoE+ (up to 36 watts) on all ports to meet the demands of greater power necessary PoE network applications with Gigabit speed transmission. It flawlessly satisfies the power needs of PoE VoIP phones, PoE Wireless APs, and all varieties of PoE IP cameras, including IR, PTZ, speed dome cameras, and even box-style IP cameras with an integrated fan and heater for high power consumption.Because there are no longer any limitations on where network devices can be placed near power outlets, the IGS-604HPT-RJ's PoE features also assist in lowering deployment costs. Power and data switching are combined into a single device that is managed centrally and delivered via a single connection. Thus, it eliminates the need for extra AC wire and speeds up installation.
Built-in Special PoE Features for Management of Surveillance
The IGS-604HPT-RJ is a managed PoE switch with sophisticated PoE management features for a surveillance network.Scheduled Power Recycling and PD Alive CheckPoE Schedule SMTP/SNMP Trap Event Alert
Alive Check for Intelligent Powered Device
The IGS-604HPT-RJ can be set up to use ping action to continuously track the status of a connected PD (Powered Device). The IGS-604HPT-RJ will restart the PoE port power and restart the PD once it stops functioning and is silent. Through the PoE port resetting the PD's power source, it will considerably improve network reliability while lessening the administrative cost.
Recycled Power on Schedule
Each of the connected PDs may reboot once a week at a predetermined time thanks to the IGS-604HPT-RJ. As a result, it will lessen the possibility of a buffer overflow-related PD crash.
SMTP/SNMP Trap Event Alert
Though most NVR or camera management software offers SMTP email alert function, the IGS-604HPT-RJ further provides event alert function to help to diagnose the abnormal device owing to whether or not there is a break of the network connection, loss of PoE power or the rebooting response by the PD Alive Check process.
Alert for SMTP/SNMP Trap Events
Although the majority of NVR or camera management software provides SMTP email alert functionality, the IGS-604HPT-RJ additionally offers event alert functionality to help identify abnormal devices caused by network connection loss, PoE power loss, or a device rebooting in response to the PD Alive Check process.
Fast Recovery for Critical Network Applications with Redundant Ring
To avoid disruptions and outside intrusions, the IGS-604HPT-RJ utilizes redundant ring technology and has a powerful, quick self-recovery capability. To increase system dependability and uptime in challenging factory conditions, it integrates modern ITU-T G.8032 ERPS (Ethernet Ring Protection Switching) technology, Spanning Tree Protocol (802.1s MSTP), and redundant power input system. The recovery time of a data link in a certain, straightforward Ring network can be as quick as 20ms.
Dual IPv6/IPv4 Stack
Data centers, campuses, telecommunications, and other organizations can experience the IPv6 era with the least amount of investment thanks to the IGS-604HPT-RJ's support for both IPv6 and IPv4 protocols. This is because its network facilities do not need to be changed or upgraded if an IPv6 FTTx edge network is put up.
Layer 3 VLAN Routing for Secure and Flexible Management using IPv4 and IPv6
The IGS-604HPT-RJ offers layer 3 IPv4/IPv6 VLAN routing, which enables crossover between different VLANs and different IP addresses for the purpose of having a highly-secure, flexibly-managed, and straightforward networking application. It also offers ultra high transmission performance, excellent layer 2 and layer 4 technologies.
Dependable Layer 2 features
Advanced switch management features like dynamic port link aggregation, Q-in-Q VLAN, private VLAN, Multiple Spanning Tree Protocol (MSTP), Layer 2 to Layer 4 QoS, bandwidth control, and IGMP/MLD Snooping can be programmed into the IGS-604HPT-RJ. The IGS-604HPT-RJ enables the operation of a high-speed trunk to combine with numerous fiber ports and offers fail-over via link aggregation of supporting ports.
Ordering Information
IGS-604HPT-RJ Industrial IP67-rated 4-Port 10/100/1000T 802.3at PoE + 2-Port 10/100/1000T Managed Ethernet Switch (-40~75 degrees C)
Datasheet
Surveillance System High Availability Networking Solution
Strong, quick self-recovery capabilities allow the IGS-604HPT-RJ to stop disruptions and outside intrusions. To increase system dependability and uptime, it integrates ITU-T G.8032 ERPS (Ethernet Ring Protection Switching) into the automation network of the customer. The IGS-604HPT-RJ is the best option for surveillance systems to establish high bandwidth for public transmission systems and railway transmission while also establishing redundant connections.
Application of Layer 3 VLAN Routing with PoE
The IGS-604HPT-RJ enables dependable routing between VLANs and network segments thanks to the integrated, powerful Layer 3 routing protocols. By using a VLAN interface with up to 32 routing entries, routing protocols can be deployed. The IGS-604HPT-RJ offers better security, control, and bandwidth conservation in addition to high-speed uplink, making it unquestionably the best option for industries.
Purchase Information
Industrial 4-Port 10/100/1000T 802.3at PoE + 2-Port 10/100/1000T Managed Ethernet Switch, IGS-604HPT-RJ, Rated IP67 (-40 to 75 degrees C)
Related Products
We Bluboxx Communication Provides wide range Ring Managed Gigabit Ethernet Switches.
The IGS-604HPT-RJ features strong, rapid, self-recovery capability to prevent interruptions and external intrusions. It incorporates ITU-T G.8032 ERPS (Ethernet Ring Protection Switching) into customer’s automation network to enhance system reliability and uptime. The IGS-604HPT-RJ is the ideal solution for surveillance system to build redundant connection and establish high bandwidth for public transmission system and railway transmission.
With the built-in, robust Layer 3 routing protocols, the IGS-604HPT-RJ ensures reliable routing between VLANs and network segments. The routing protocols can be applied by VLAN interface with up to 32 routing entries. The IGS-604HPT-RJ, certainly an ideal solution for industries, offers greater security, control and bandwidth conservation, and high-speed uplink.
We Provide complete Industrial Networking Solutions in Pune, Mumbai, Kolkata, Bangalore, Chennai, Hyderabad, Delhi, Noida, Thane, Indore, Jaipur, Nagpur, Mangalore, Nashik, Coimbatore, Bhopal, Baroda, Surat, Ahmedabad, GOA, Gurgaon, PAN India