Search Products


WGS-5225-8P2S

Industrial L2+ 8-Port 10/100/1000T 802.3at PoE + 2-Port 100/1000X SFP Wall-mount Managed Switch

 

  • Description
  • Specification
  • Application

Advanced L2+/L4 Switching, Wall-mount PoE Managed Switch, and Security

An industrial wall-mount PoE managed switch called the PLANET WGS-5225-8P2S uses PLANET intelligent PoE capabilities to increase the availability of industrial applications. It has two additional 1000BASE-X SFP ports, eight 10/100/1000BASE-T ports with 36-watt PoE, built-in L2+/L4 Gigabit switching engine, IPv6/IPv4 dual stack management, and eight 10/100/1000BASE-T ports. The WGS-5225-8P2S is a perfect option to meet the demand for the following network applications, with a total power budget of up to 240 watts for various PoE applications, networking speed, and operating temperature ranging from -40 to 75 degrees C in a small but durable IP30 metal housing.

 

Home and building automation network

IoT, or the internet of things

IP monitoring

Fast Recovery for Critical Network Applications with Redundant Ring

To avoid disruptions and outside intrusions, the WGS-5225-8P2S utilizes redundant ring technology and has a powerful, quick self-recovery capacity. To increase system dependability and uptime in challenging factory conditions, it integrates modern ITU-T G.8032 ERPS (Ethernet Ring Protection Switching) technology, Spanning Tree Protocol (802.1s MSTP), and dual power input system. The recovery time of a data link in a specific basic ring network can be as quick as 10ms.

ONVIF devices having a detection feature that are practical and smart

A fantastic new feature from PLANET called ONVIF Support was created expressly to work with video IP surveillance systems. You only need one click from the WGS-5225-8P2S's GUI to search and display every ONVIF device using network application. Additionally, the switch allows you to upload floor photos and remotely monitor or check an assembly line. Additionally, you may get real-time surveillance data, online/offline status, and GUI-controlled PoE reboots.

Built-in Special PoE Features for Managed Powered Devices

The WGS-5225-8P2S has the following unique PoE management features since it is the managed PoE switch for surveillance, WLAN, and VoIP networks:

Check for PD life
Periodic power recycling
PoE timetable
PoE use analysis
Alive Check for Intelligent Powered Device

The WGS-5225-8P2S can be set up to use ping action to continuously track the connected PD status. The WGS-5225-8P2S will restart the PoE port power and restart the PD when it stops operating and responding, restoring its functionality. Through the PoE port's capacity to reset the PD's power source and lessen the administrative workload, it will significantly improve network dependability.

Recycled Power on Schedule

Each of the connected PoE IP cameras or PoE wireless access points can reboot on a weekly schedule thanks to the WGS-5225-8P2S. As a result, it will lessen the likelihood that a buffer overflow may cause an IP camera or AP to crash.

Schedule of Energy for PoE

The WGS-5225-8P2S can efficiently control the power supply in accordance with the global trend of energy conservation and contribute to environmental protection in addition to its capacity to deliver high watts of power. The "PoE schedule" function is a potent tool for SMBs or enterprises to conserve money and power since it allows you to enable or disable PoE power feeding for each PoE port during predetermined time intervals. By turning off PDs that should not be in use outside of work hours, it also improves security.

Contemporary Wall-mount Installation

The WGS-5225-8P2S is specifically made to be put in a small space, like an electrical box or wall enclosure. Any place with limited room may readily accommodate the small, flat, and wall-mounted design. It uses the user-friendly "Front Access" design, which makes it very simple for personnel to install, cable wire, monitor, and maintain the WGS-5225-8P2S when it is housed in an enclosure. The WGS-5225-8P2S's versatility in use is increased by the fact that it may be mounted on a fixed wall, a magnetic wall, or a DIN rail.

Alert for SMTP/SNMP Trap Events

The WGS-5225-8P2S offers an event alert capability to assist in diagnosing an abnormal device caused by a network connection failure or a rebooting reaction.

Layer 3 Software VLAN Routing for Secure and Flexible Management using IPv4 and IPv6

The WGS-5225-8P2S helps customers stay on top of their businesses by offering excellent Layer 2 technologies, ultra-high transmission performance, and IPv4/IPv6 software VLAN routing. This feature enables customers to cross different VLANs and IP addresses for the purpose of having a more straightforward networking application and a highly secure, flexible management environment.

Dependable Layer 2 features

Advanced switch management features like dynamic port link aggregation, Q-in-Q VLAN, private VLAN, Rapid Spanning Tree Protocol, Layer 2 to Layer 4 QoS, bandwidth control, and IGMP snooping can be programmed into the WGS-5225-8P2S. The WGS-5225-8P2S offers 802.1Q tagged VLAN, with a maximum of 255 VLAN groups permitted. The WGS-5225-8P2S enables the operation of a high-speed trunk combining numerous ports through the aggregation of supporting ports. It supports fail-over and allows for a maximum of two trunk groups with two ports each.

A Mechanism for Intelligent SFP Diagnosis

The SFP-DDM (Digital Diagnostic Monitor) capability is supported by the WGS-5225-8P2S, which makes it much easier for network administrators to simply keep track of real-time SFP parameters such optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage.

Purchase Information
IGS-6325-8T8S Industrial L3 8-Port 10/100/1000T + 8-Port 100/1000X SFP Managed Ethernet Switch

Hardware Specifications
Copper Ports8 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
SFP Ports8 100/1000BASE-X SFP slot interfaces (Port-9 and Port-16)
Compatible with 100BASE-FX SFP transceiver
SFP+ Ports--
Console1 x RJ45-to-RS232 serial port (115200, 8, N, 1)
Switch ArchitectureStore-and-Forward
Switch Fabric32Gbps/non-blocking
Throughput23.81Mpps@64Bytes
Address Table16K entries, automatic source address learning and aging
Shared Data Buffer32Mbits
Jumbo Frame10K bytes
SDRAM512Mbytes
Flash Memory64Mbytes
Flow ControlIEEE 802.3x pause frame for full duplex
Back pressure for half duplex
Reset Button< 5 sec: System reboot
> 5 sec: Factory default
ConnectorRemovable 6-pin terminal block for power input
Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin 5/6 for Power 2
Removable 6-pin terminal block for DI/DO interface
Pin 1/2 for DI 1 & 2, Pin 3/4 for DO 1 & 2, Pin 5/6 for GND
AlarmOne relay output for power failure. Alarm relay current carry ability: 1A @ 24V DC
Digital Input (DO)2 digital input:
 Level 0: -24~2.1V (±0.1V)
 Level 1: 2.1~24V (±0.1V)
 Input load to 24V DC, 10mA max.
Digital Output (DO)2 digital output:
 Open collector to 24VDC, 100mA
EnclosureIP30 aluminum case
InstallationDIN-rail or wall mounting
Dimensions (W x D x H)76.8 x 107.3 x 152 mm
Weight1,065g
Power RequirementsDC 12~48V, 4A max.
AC 24V, 2A max.
Power ConsumptionDC input:
Max. 9.12 watts/32BTU
(system on)
Max. 26.04 watts/89 BTU (Full loading)

AC 24V input:
Max. 12 watts/41BTU (system on)
Max. 29 watts/99 BTU (Full loading)
ESD Protection6KV DC
Surge Protection4KV DC
LED IndicatorsSystem:
 Power 1 (Green), Power 2 (Green)
 Fault Alarm (Red)
 Ring (Green), Ring Owner (Green)
 DIDO (Red)
Per 10/100/1000T RJ45 Port:
 1000Mbps LNK/ACT (Green)
 10/100Mbps LNK/ACT (Amber)
Per SFP Port:
 1000Mbps LNK/ACT (Green)
 100Mbps LNK/ACT (Amber)
Layer 2 Functions
Port ConfigurationPort disable/enable
Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
Flow control disable/enable
Port link capability control
Port StatusDisplay each port’s speed duplex mode, link status, flow control status, auto-negotiation status, trunk status
Port MirroringTX/RX/Both
Many-to-1 monitor
VLAN802.1Q tagged VLAN
Q-in-Q tunneling
Private VLAN Edge (PVE)
MAC-based VLAN
Protocol-based VLAN
Voice VLAN
IP Subnet-based VLAN
MVR (Multicast VLAN registration)
GVRP
Up to 256 VLAN groups, out of 4095 VLAN IDs
Link AggregationIEEE 802.3ad LACP/static trunk
14 trunk groups with 16 port per trunk group
Spanning Tree ProtocolIEEE 802.1D Spanning Tree Protocol
IEEE 802.1w Rapid Spanning Tree Protocol
IEEE 802.1s Multiple Spanning Tree Protocol
IGMP SnoopingIPv4 IGMP (v1/v2/v3) snooping
IPv4 IGMP querier mode support
Supports 255 IGMP groups
MLD SnoopingIPv6 MLD (v1/v2) snooping,
IPv6 MLD querier mode support
Supports 255 MLD groups
Access Control ListIP-based ACL/MAC-based ACL
ACL bBased on:
 - MAC Address
 - IP Address
 - Ethertype
 - Protocol Type
 - VLAN ID
 - DSCP
 - 802.1p Priority
Up to 256 entries
Bandwidth ControlPer port bandwidth control
Ingress: 100Kbps~1000Mbps
Egress: 100Kbps~1000Mbps
QoSTraffic classification based, strict priority and WRR
8-level priority for switching:
 - Port number
 - 802.1p priority
 - 802.1Q VLAN tag
 - DSCP/ToS field in IP packet
SynchronizationIEEE 1588v2 PTP(Precision Time Protocol)
 - Peer-to-peer transparent clock
 - End-to-end transparent clock
Layer 3 Functions
IP InterfacesMax. 128 VLAN interfaces
Routing TableMax. 128 routing entries
Routing ProtocolsIPv4 hardware static routing
IPv6 hardware static routing
OSPFv2 dynamic routing
Management
Basic Management InterfacesConsole; Telnet; Web browser; SNMP v1, v2c
Secure Management InterfacesSSHv1/v2, TLS, SSL, SNMPv3
System ManagementFirmware upgrade by HTTP protocol through Ethernet network
Configuration upload/download through HTTP
Remote Syslog
System log
LLDP protocol
NTP
PLANET Smart Discovery Utility
SNMP MIBsRFC 1213 MIB-II
RFC 1493 Bridge MIB
RFC 1643 Ethernet MIB
RFC 2863 Interface MIB
RFC 2665 Ether-Like MIB
RFC 2819 RMON MIB (Group 1, 2, 3 and 9)
RFC 2737 Entity MIB
RFC 2618 RADIUS Client MIB
RFC 2863 IF-MIB
RFC 2933 IGMP-STD-MIB
RFC 3411 SNMP-Frameworks-MIB
RFC 4292 IP Forward MIB
RFC 4293 IP MIB
RFC 4836 MAU-MIB
IEEE 802.1X PAE
LLDP
Standards Conformance
Regulatory ComplianceFCC Part 15 Class A
CE:
EN55032
EN55035
EN 62368-1/IEC 62368-1: 2014
Stability TestingIEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)
Standards ComplianceIEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX/100BASE-FX
IEEE 802.3z Gigabit SX/LX
IEEE 802.3ab Gigabit 1000T
IEEE 802.3x flow control and back pressure
IEEE 802.3ad port trunk with LACP
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1w Rapid Spanning Tree Protocol
IEEE 802.1s Multiple Spanning Tree Protocol
IEEE 802.1p Class of Service
IEEE 802.1Q VLAN tagging
IEEE 802.1X Port Authentication Network Control
IEEE 802.1ab LLDP
IEEE 802.3ah OAM
IEEE 802.1ag Connectivity Fault Management (CFM)
RFC 768 UDP
RFC 793 TFTP
RFC 791 IP
RFC 792 ICMP
RFC 2068 HTTP
RFC 1112 IGMP v1
RFC 2236 IGMP v2
ITU-T G.8032 ERPS Ring
ITU-T Y.1731 Performance Monitoring
Environment
Operating-40 ~ 75 degrees C
Storage-40 ~ 85 degrees C
Humidity5 ~ 95% (non-condensing)

 

Building Security Automation Switch

The WGS-5225-8P2SV provides a thorough Layer 2 to Layer 4 Access Control List (ACL), making it ideal for facilities where security must be strictly maintained. By rejecting packets based on source and destination IP addresses, TCP/UDP ports, or predefined standard network applications, the switch can impose restrictions on network access. A tightly controlled network can be quickly and readily obtained with the WGS-5225-8P2SV.

Various Networks Controlled by a single center

The WGS-5225-8P2SV can centrally manage power supplying to an industrial network system where IP phones, IP cameras, wireless APs, and more are installed by offering up to 8 PoE+, in-line power interfaces. For example, in an industrial setting, 8 PoE IP cameras or wireless access points can be quickly put around the corner for wireless roaming or surveillance needs. The WGS-5225-8P2SV removes the power-socket restriction, which allows the installation of IP cameras and wireless APs simpler and more effective.